Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. Hinged elements of a body
8.1.1. Removal and installation of a cowl
8.1.2. Check and adjustment of a cowl
8.1.3. Removal and installation of a forward wing
8.1.4. Removal and installation of a forward door
8.1.5. Removal and installation of a door of a back (for models with a body the versatile person)
8.1.6. Removal and installation of a trunk lid (for models with a body the sedan)
8.2. Finishing of a body
8.3. Body glazing
9. Schemes of electric equipment
 






8-1-5-snyatie-i-ustanovka-dveri-zadka-dlya-modelejj-s-kuzovom-universal.html

8.1.5. Removal and installation of a door of a back (for models with a body the versatile person)

Fig. 8.12. Back door elements (for models with a body the versatile person): 1 – back door panel; 2 – back door window glass; 3 – back door loop; 4 – back door equalizer; 5 – finishing of a door of a back; 6 – back door glass fringing; 7 – backing lamp; 8 – overlay of a door of a back; 9 – a back door spoiler (if is available)


Fig. 8.13. Elements of a back door: 1 – door panel; 2 – door loop; 3 – door limiter; 4 – bolt of a loop of a back door; 5 – bolt of the limiter of opening of a door; 6 – sealant of an aperture of a back door



Removal
Remove finishing of a door of a back.
Remove a back part of an internal upholstery of a roof and back facings.

Fig. 8.14. Removal of a door of a back


Disconnect sockets of a plait of a door of a back 1 and a hose of a washer of 2 (fig. 8.14).
Remove stabilizers of a door of a back of 3 (fig. 8.14).
Turn off nuts of loops of a door 4 and remove a door of a back of 5 (fig. 8.14).

Handling of the back door stabilizer (damper)
Handle with the stabilizer with care. Do not allow damage of a surface of a rod of the piston, and also hit on it of paint or oil.
Do not rotate a piston rod if he is completely nominated.
Do not disassemble the stabilizer 1 because its cylinder is filled with gas.

Utilization of the stabilizer of a door of a back (damper)

Fig. 8.15. Utilization of a damper of a door of a back


Gas which filled the stabilizer does not constitute danger, but when drilling an opening in the cylinder it can leave an opening with high speed taking out with itself(himself) the metal shaving which is formed during the work of a drill of 2 (fig. 8.15). Therefore always put on goggles.
Before utilization, using a drill with a diameter of 2-3 mm, make by means of a drill the 2nd opening for removal of gas of the stabilizer cylinder.

Installation
Installation is made as it should be, the return to removal, taking into account the following.

Fig. 8.16. Fixing of a plait of wires


Fix a plait of wires (fig. 8.16).
Adjust the provision of a clamp of the lock of a door.
Adjust a door emphasis so that the door was aflush with a body in the closed state.

Fig. 8.17. Loop and emphasis of a door of a back


Apply sealant on the surfaces of contact of "A" of a door loop 1 and jellied lubricant on the rotating parts of "B" of the hinge 1 (fig. 8.17).

"previous page
8.1.4. Removal and installation of a forward door
following page"
8.1.6. Removal and installation of a trunk lid (for models with a body the sedan)