Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
4.1. Diagnostics of malfunctions of a suspension bracket, disks and tires
4.2. Wheels and tires
4.3. Forward suspension bracket
4.4. Back suspension bracket
4.4.1. Angles of installation of back wheels
4.4.2. Check and adjustment of angles of installation of back wheels
4.4.3. Check and adjustment of a convergence
4.4.4. Removal and installation of a bar of the stabilizer of a back suspension bracket and/or plugs
4.4.5. Check of a bar of the stabilizer of a back suspension bracket, plug and/or rack
4.4.6. Removal and installation of a rack of a back suspension bracket assembled
4.4.7. Dismantling and assembly of a rack of a back suspension bracket assembled
4.5. Tables
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 






4-4-6-snyatie-i-ustanovka-stojjki-zadnejj-podveski-v-sbore.html

4.4.6. Removal and installation of a rack of a back suspension bracket assembled

Fig. 4.82. Details of a rack of a back suspension bracket assembled: 1 – top cover of a rack; 2 – top nut of a rack; 3 – rack support; 4 – top basic cup of a spring; 5 – cup (rubber) of a spring; 6 – protection cover of a rack; 7 – compression buffer; 8 – cylindrical spring; 9 – lower basic cup of a spring; 10 – rack; 11 – rack support nut; 12 – rack arm nut; 13 – rack arm bolt; 14 – coupling nut of the stabilizer; 15 – stabilizer coupling



Removal
Lift the car before unloading of a back suspension bracket.

NOTE
At service of components of a rack of a suspension bracket, remove a rubber cover, then weaken a rack nut before removal of a rack a little. It will facilitate work. Pay attention, however, that at the same time the nut should not turn away completely.

Remove a wheel.
Remove the stabilizer 1 hinge from a rack arm.

Fig. 4.83. Hinge of the stabilizer and E-shaped ring of fastening of a brake hose


Remove an E-shaped ring 2 fastenings of a brake hose (fig. 4.83).
Turn off a bolt of fastening of a plait of the sensor of speed of a wheel of anti-blocking system of brakes (if is available).

Fig. 4.84. Bolts and nuts of an arm of a rack




Fig. 4.85. Nuts of a support are resistant


Turn off bolts and nuts of an arm of a rack. Then remove a brake hose from a rack arm, you watch to deforming the brake highway (fig. 4.85).
Turn off nuts of a support of a rack of 1 (fig. 4.85).
Hold a rack hands so that it did not drop out.
Remove a rack assembled.

Installation

Fig. 4.86. Installation of a rack assembled


Establish a rack as it should be, the return to removal. Establish arm bolts, as shown in the drawing (fig. 4.86).
Tighten all elements of fastening the nominal moment.

Inhaling moment
Nut of a support of a rack (a): 28 N · m.
Nut of an arm of a rack (b): 90 N · m.
Nut of the hinge of the stabilizer (c): 50 N · m.

NOTE
Do not overwind a brake hose at installation. Establish an E-shaped ring 1 on an arm 2, as shown in the figure 4.86.

"previous page
4.4.5. Check of a bar of the stabilizer of a back suspension bracket, plug and/or rack
following page"
4.4.7. Dismantling and assembly of a rack of a back suspension bracket assembled