Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
4.1. Diagnostics of malfunctions of a suspension bracket, disks and tires
4.2. Wheels and tires
4.3. Forward suspension bracket
4.3.1. Adjustment of angles of installation of forward wheels
4.3.2. Check and adjustment of angles of installation of forward wheels
4.3.3. Check and adjustment of angles of rotation of the operated wheels
4.3.4. Removal and installation of a bar of the stabilizer of a forward suspension bracket and/or plugs
4.3.5. Check of a bar of the stabilizer of a forward suspension bracket, plug and/or hinge
4.3.6. Removal and installation of a rack of a forward suspension bracket assembled
4.3.7. Dismantling and assembly of a rack of a forward suspension bracket assembled
4.3.8. Check of a rack of a forward suspension bracket assembled
4.3.9. Removal and installation of a nave of a forward wheel and rotary fist
4.3.10. Dismantling and assembly of a nave of a forward wheel and rotary fist
4.3.11. Removal and installation of the lever of the suspension bracket / plug
4.3.12. Dismantling and assembly of the lever of the suspension bracket / plug
4.3.13. Removal and installation of a stretcher of a forward suspension bracket
4.4. Back suspension bracket
4.5. Tables
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 










4-3-6-snyatie-i-ustanovka-stojjki-perednejj-podveski-v-sbore.html

4.3.6. Removal and installation of a rack of a forward suspension bracket assembled

Fig. 4.25. Details of a rack of a forward suspension bracket assembled: 1 – rack assembled; 2 – cylindrical spring; 3 – compression buffer; 4 – lower basic cup of a cylindrical spring; 5 – top basic cup of a cylindrical spring; 6 – rack bearing; 7 – rack support; 8 – rack nut; 9 – rack support nut; 10 – rack arm bolt: establish from a forward part of the car; 11 – rack arm nut; 12 – rubber cover; 13 – coupling nut of the stabilizer; 14 – stabilizer coupling



Removal
Lift the car before unloading of a forward suspension bracket.

NOTE
At service of components of a rack of a suspension bracket, remove a rubber cover, then weaken a rack nut before removal of a rack a little. It will facilitate work. Pay attention, however, that at the same time the nut should not turn away completely.


Fig. 4.26. Stabilizer rack arm


Remove a wheel and disconnect a stabilizer 1 rack from an arm of a rack (fig. 4.26).

Fig. 4.27. Bolts of fastening of a brake hose and arm of a rack


Turn off a bolt of fastening of a brake hose 1 and disconnect a brake hose 2, and then a plait of the sensor of speed of a wheel of anti-blocking system of brakes (if is available) from a rack arm, as shown in the figure 4.27.
Turn off bolts of an arm of a rack 4.

Fig. 4.28. Nuts of a support are resistant


Turn off nuts of a support of a rack of 1 (fig. 4.28).

NOTE
Hold a rack hands so that it did not drop out.

Remove a rack assembled.

Installation
Establish a suspension bracket rack in the return sequence, taking into account the following.
Establish bolts, as shown in the figure 4.28.
Delay all fastenings by the nominal force of an inhaling.

Inhaling moment
Nut of an arm of a rack (a): 105 N · m.
Nut of a support of a rack (b): 28 N · m.
Bolt of fastening of a brake hose (c): 25 N · m.
Nut of the stabilizer (d): 50 N · m.

NOTE
Do not overwind a brake hose and a plait of the sensor of speed of anti-blocking system of brakes (if is available).


Fig. 4.29. Installation of a rack assembled


Establish a plait of the sensor of speed of anti-blocking system of brakes (if is available), as shown in the figure 4.29.
Tighten a wheel nut the nominal force of an inhaling.
Wheel nut inhaling moment: 85 N · m.
After installation check the angles of installation of forward wheels.

"previous page
4.3.5. Check of a bar of the stabilizer of a forward suspension bracket, plug and/or hinge
following page"
4.3.7. Dismantling and assembly of a rack of a forward suspension bracket assembled