Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
4.1. Diagnostics of malfunctions of a suspension bracket, disks and tires
4.2. Wheels and tires
4.3. Forward suspension bracket
4.3.1. Adjustment of angles of installation of forward wheels
4.3.2. Check and adjustment of angles of installation of forward wheels
4.3.3. Check and adjustment of angles of rotation of the operated wheels
4.3.4. Removal and installation of a bar of the stabilizer of a forward suspension bracket and/or plugs
4.3.5. Check of a bar of the stabilizer of a forward suspension bracket, plug and/or hinge
4.3.6. Removal and installation of a rack of a forward suspension bracket assembled
4.3.7. Dismantling and assembly of a rack of a forward suspension bracket assembled
4.3.8. Check of a rack of a forward suspension bracket assembled
4.3.9. Removal and installation of a nave of a forward wheel and rotary fist
4.3.10. Dismantling and assembly of a nave of a forward wheel and rotary fist
4.3.11. Removal and installation of the lever of the suspension bracket / plug
4.3.12. Dismantling and assembly of the lever of the suspension bracket / plug
4.3.13. Removal and installation of a stretcher of a forward suspension bracket
4.4. Back suspension bracket
4.5. Tables
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 










4-3-7-razborka-i-sborka-stojjki-perednejj-podveski-v-sbore.html

4.3.7. Dismantling and assembly of a rack of a forward suspension bracket assembled

Dismantling

Fig. 4.30. Compression of a spring by means of adaptation


At established on a spring, as shown in the figure 4.30, the special tool (A) serially tighten bolts of the special tool until details of a rack are not exempted from loading from a spring. If the rack can turn at a motionless spring of a rack, then it is possible to consider that the spring is compressed enough.

ATTENTION
Use a stripper of springs and follow the operating procedure described in the instruction to a stripper of springs.


Fig. 4.31. Otvorachivany nuts of fastening are resistant


Without removing from a spring of the special tool, turn off a nut of a rack (fig. 4.31).
Sort a suspension bracket rack.

Assembly
Assembly is made as it should be, the return to dismantling, in view of the following.

Fig. 4.32. Compression of a spring special tool: U – top party (big diameter); L – to lower the party (small diameter)


Squeeze a spring the special tool (A) so that its full length made about 250 mm, as shown in the figure 4.32.

Length
"a": 250 mm (9.8 inches.), for cars with a body "hatchback".
"a": 230 mm (9.0 inches.), for cars with a body "sedan".

Fig. 4.33. Installation of a spring on the lower basic cup


Install the lower basic cup of a cylindrical spring 1 and a cylindrical spring, the end of a spring has to get to a ledge in the lower basic cup, as shown in the figure 4.33.
Install the buffer of compression and the protection cover on a rack rod.
Extend a rack rod as far as possible and you watch that it did not come back to a rack.

Fig. 4.34. Installation of a plate of a spring and top basic cup


Install a plate of a spring on a spring, then install the top basic cup 1, having combined tags 3 on the top basic cup of a spring and the center of an arm of a rack of 2 (fig. 4.34).

Fig. 4.35. Final assembly of a rack


Install the bearing 3, a support of a rack 2 and a nut 1 observing the sequence (fig. 4.35).
Tighten a rack nut 1 nominal force of an inhaling.
Moment of an inhaling of a nut of fastening of a rack (a): 70 N · m.
Establish a rubber cover 4.

"previous page
4.3.6. Removal and installation of a rack of a forward suspension bracket assembled
following page"
4.3.8. Check of a rack of a forward suspension bracket assembled