Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
2.1. Preliminary checks
2.2. Mechanical part of engines
2.3. Engine cooling system
2.3.1. General information
2.3.2. Diagnostic information and procedures
2.3.3. Removal and installation of tubes or hoses of the cooling system
2.3.4. Removal and installation of the thermostat
2.3.5. Check of the thermostat
2.3.6. Removal and installation of the valve in a throttle branch pipe (if is available)
2.3.7. Check on the cooling system radiator fan car
2.3.8. Check of the relay of the fan of the cooling system
2.3.9. Removal and installation of the fan of the cooling system
2.3.10. Check and cleaning of a radiator on the car
2.3.11. Removal and installation of a radiator
2.3.12. Check and adjustment of a tension of a driving belt of the pump of cooling liquid / generator
2.3.13. Removal and installation of a driving belt of the pump of cooling liquid / generator
2.3.14. Removal and installation of the pump of cooling liquid
2.3.15. Check of the pump of cooling liquid
2.4. Engine lubrication system
2.5. Fuel system
2.6. System of ignition
2.7. System of release
2.8. The engine and system of decrease in toxicity of the fulfilled gases (M13 and M16 engines)
2.9. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 






2-3-4-snyatie-i-ustanovka-termostata.html

2.3.4. Removal and installation of the thermostat

Fig. 2.183. Cooling system elements: 1 – radiator; 2 – broad tank; 3 – radiator stopper; 4 – drain stopper; 5 – the taking-away radiator hose; 6 – the bringing radiator hose; 7 – thermostat; 8 – ECT sensor; 9 – thermostat case; 10 – to a head of the block of cylinders; 11 – to a throttle branch pipe; 12 – to a heater radiator; 13 – to the pump of cooling liquid; 14 – radiator fan; 15 – the bringing pipe of the cooling system No. 1; 16 – the bringing pipe of the cooling system No. 2; 17 – thermostat cover; 18 – cover of an exhaust outlet; 19 – the bringing heater radiator hose; 20 – the taking-away heater radiator hose; 21 – to a gas distribution mechanism drive chain cover; 22 – sealing ring; 23 – laying; 24 – sealing ring of a cover of an exhaust outlet No. 1; 25 – sealing ring of a cover of an exhaust outlet No. 2; 26 – thermostat cover bolts; 27 – thermostat case bolts; 28 – a hose of circulation of a radiator of a heater (if is available); 29 – the condenser fan (if is available); 30 – the valve (if is available); 31 – inlet valve of a throttle branch pipe; 32 – final valve of a throttle branch pipe; 33 – to a head of the block of cylinders; 34 – to the thermostat case; 35 – throttle branch pipe +



Removal
Merge liquid from system having weakened a drain stopper of a radiator.
Take out the air filter assembled with the resonator.
Remove an inlet collector.

Fig. 2.184. Engine cooling system hoses



Remove the generator.
Disconnect hoses of the cooling system 1 and hoses of a radiator of a heater 2 from tubes.
Remove the thermostat 3 case with a cover of the thermostat 4 and the bringing pipe 5.

Fig. 2.185. The case of the thermostat and the bringing tubes



Remove the bringing cooling system pipe with a thermostat cover from the thermostat case.
Take out the thermostat.

Installation
Installation is made as it should be, the return to removal, except for the following.

Fig. 2.186. Assembly of the case of the thermostat


At installation of the thermostat 1 in the case of the thermostat 2 be convinced that the valve for production of air 3 is in the situation shown in the figure 2.186.
At installation use new sealing rings.
Adjust a tension of a belt of the drive of the pump of cooling liquid.
Adjust a tension of a belt of the drive of the compressor of the air conditioning system (if is available).
Fill the cooling system.
Be convinced of lack of leak of cooling liquid from connections of the cooling system.

"previous page
2.3.3. Removal and installation of tubes or hoses of the cooling system
following page"
2.3.5. Check of the thermostat