Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
2.1. Preliminary checks
2.2. Mechanical part of engines
2.3. Engine cooling system
2.4. Engine lubrication system
2.5. Fuel system
2.6. System of ignition
2.7. System of release
2.8. The engine and system of decrease in toxicity of the fulfilled gases (M13 and M16 engines)
2.8.1. Electronic control system
2.8.2. Service on the car
2.8.3. Control unit of the engine of an electronic control system (electronic control unit)
2.8.4. The sensor of absolute pressure in a collector
2.8.5. Sensor of provision of a butterfly valve
2.8.6. The air temperature sensor on an admission
2.8.7. Sensor of temperature of cooling liquid of the engine
2.8.8. The sensor of concentration of oxygen with heating (the sensor of concentration of oxygen with heating No. 1 and the sensor of concentration of oxygen with heating No. 2)
2.8.9. Check of the sensor of provision of a cam-shaft
2.8.10. Check of the sensor of provision of a bent shaft
2.8.11. Main relay, relay of the fuel pump, relay of the compressor of the air conditioning system and relay of the fan of the condenser of the air conditioning system
2.8.12. Check of a control system of the fan of a radiator
2.8.13. Check of the filter of system of catching of vapors of gasoline of system of decrease in toxicity of the fulfilled gases
2.8.14. Check of the filter of system of catching of vapors of gasoline
2.8.15. System of ventilation of a case
2.9. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 






2-8-5-datchik-polozheniya-drosselnojj-zaslonki.html

2.8.5. Sensor of provision of a butterfly valve

Check
Disconnect a wire from a negative conclusion of the rechargeable battery and I will corrode from the air temperature sensor on an admission.
Remove the air filter assembled with the taking-away hose and disconnect the socket of the sensor of provision of a butterfly valve.

Fig. 2.277. Check of the sensor of provision of a butterfly valve: 1 – conclusion of basic tension; 2 – conclusion of output tension; 3 – weight conclusion


Using an ohmmeter, check resistance between conclusions according to the table (fig. 2.277) given below.
If the result of check does not meet standard, replace the sensor of provision of a butterfly valve.

NOTE
The difference of indications of an ohmmeter at completely open and completely closed butterfly valve has to be not less than 2 kOhm.

Connect the socket of the sensor of provision of a butterfly valve.
Connect a wire to a negative conclusion of the rechargeable battery.

Removal
Disconnect a wire from a negative conclusion of the rechargeable battery.
Remove a throttle branch pipe from an inlet collector.
Remove the sensor of provision of a butterfly valve from a throttle branch pipe.

Installation

Fig. 2.278. Installation of the sensor of provision of a butterfly valve


Install the sensor of provision of a butterfly valve 1 on a throttle branch pipe (fig. 2.278).
Install the sensor of provision of a butterfly valve on a throttle branch pipe so that its openings 3 were at some distance from openings under the screw of the sensor of provision of a butterfly valve 2, as shown in the left drawing, and turn the sensor of provision of a butterfly valve clockwise so that openings were combined by 3 (fig. 2.278).
Moment of an inhaling of the screw of the sensor of provision of a butterfly valve (a): 2,5 N · m.
Connect the socket to the sensor of provision of a butterfly valve.
Connect a wire to a negative conclusion the rechargeable battery.

"previous page
2.8.4. The sensor of absolute pressure in a collector
following page"
2.8.6. The air temperature sensor on an admission