Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical transmission
3.3. Automatic transmission
3.3.1. General description
3.3.2. Design of system of blocking of brakes
3.3.3. Check of level of liquid in the automatic transmission
3.3.4. Replacement of liquid in the automatic transmission
3.3.5. Removal and installation of a cable of the choice of transfer
3.3.6. Adjustment of a cable of the choice of transfer
3.3.7. Check and adjustment of the sensor of the mode of the movement (switching sensor)
3.3.8. Removal and installation of the sensor of speed of the leading shaft
3.3.9. Check of the sensor of speed of the leading shaft
3.3.10. Removal and installation of the sensor of temperature of liquid
3.3.11. Check of the sensor of temperature of liquid
3.3.12. Check of the switch of the mode of the raising transfer
3.3.13. Removal and installation of electromagnetic valves (switching valve, valve of the hydrotransformer and valve of synchronization)
3.3.14. Check of electromagnetic valves (switching valves, electromagnetic valve of the hydrotransformer and electromagnetic valve of synchronization)
3.3.15. Replacement of an epiploon from differential
3.3.16. Replacement of the electromagnetic device of blocking of switching
3.3.17. Removal and installation of a cable of blocking of a key
3.3.18. Replacement of hoses of a cooler of the automatic transmission
3.4. Driving mechanism
3.5. Tables
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 






3-3-17-snyatie-i-ustanovka-trosa-blokirovki-klyucha.html

3.3.17. Removal and installation of a cable of blocking of a key

NOTE
At removal and installation do not bend a blocking cable excessively, otherwise, the system will correctly not work.

Removal
If the car is equipped with system of passive safety, disconnect a wire from a negative conclusion of the rechargeable battery and disconnect system of passive safety.
Uncover a steering column.
Turn the ignition key in position of ACC.

Fig. 3.116. Blocking cable pulling


Extend a cable of blocking of a key 1 of a cover of the cylinder of the lock 2 pressing a clamp the screw-driver with flat shliyets of 3 (fig. 3.116).
Turn the ignition key in position of LOCK.
Remove facing of the drive of the parking brake system and the console.
Disconnect the end of a cable 1 from a cam of blocking 2, having pressed ledges 3 on inflow of a cam.

Fig. 3.117. Removal of a cable of blocking


You watch to damaging ledges (fig. 3.117).
Uncover the case of a cable 4 a selector 5 arm, having pressed a clamp (fig. 3.117).
Remove a blocking cable.

Installation
Lay a blocking cable as it was laid before removal.
Turn the ignition key in position of ACC.

Fig. 3.118. Installation of a cover of the case of a cable


Establish a cover of the case of a cable 1 in a cover of the cylinder of the lock 2 (fig. 3.118).

Fig. 3.119. A pulling of the button of blocking of the end of a cable from the selector


Extend the button of 1 blocking of the end of a cable from the selector 2 (fig. 3.119).
Transfer the selector lever to situation "N".

NOTE
If the lever of the selector is in situation.


Fig. 3.120. Installation of a cable of blocking


Establish a cover of the case of a cable 3 on an arm of the selector 4 (fig. 3.120).
Connect the end of a cable 1 to a cam of blocking 2, at the same time the key in the lock of ignition has to be in position of ACC (fig. 3.120).
Put on the blocking button 5 the end of a cable before its fixing on a cable (fig. 3.120).
Install the selector lever in situation "P", turn the ignition key in position of ACC and check performance of the following conditions.
At the released button the ignition key can be turned from position of ACC in position of LOCK.
At the pressed button the ignition key cannot be turned from position of ACC in position of LOCK.
Establish a cover of a steering column.
If the car is equipped with system of passive safety, connect a wire to the negative plug of the rechargeable battery and include system of passive safety.

"previous page
3.3.16. Replacement of the electromagnetic device of blocking of switching
following page"
3.3.18. Replacement of hoses of a cooler of the automatic transmission