Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
2.1. Preliminary checks
2.1.1. Check of a driving belt
2.1.2. Replacement of an oil filter
2.1.3. Check of a compression
2.1.4. Engine vacuum check
2.1.5. Check of gaps in the drive of valves
2.1.6. Check of level of cooling liquid
2.1.7. Check and cleaning of the cooling system of the engine
2.1.8. Check of the mode of a cut-off of supply of fuel
2.1.9. Check of a spark of ignition
2.1.10. Removal and installation of a high-voltage wire
2.1.11. Check of a high-voltage wire
2.1.12. Removal and installation of a spark plug
2.1.13. Check of a spark plug
2.1.14. Removal and installation of the coil of ignition (with igniter)
2.1.15. Check of the coil of ignition (with igniter)
2.1.16. Check of installation of a corner of an advancing of ignition
2.2. Mechanical part of engines
2.3. Engine cooling system
2.4. Engine lubrication system
2.5. Fuel system
2.6. System of ignition
2.7. System of release
2.8. The engine and system of decrease in toxicity of the fulfilled gases (M13 and M16 engines)
2.9. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 






2-1-16-proverka-ustanovki-ugla-operezheniya-zazhiganiya.html

2.1.16. Check of installation of a corner of an advancing of ignition

NOTE
Adjustment of a corner of an advancing of ignition in operation is not required. If installation of a corner of an advancing of ignition – differs from norm, check system elements.
Before launch of the engine transfer the lever of gear shifting of transfers to neutral situation (the selector lever to situation "P" for models with the automatic transmission), slow down the car the parking brake system of set and record driving wheels.


Fig. 2.33. Connection of the Suzuki scanner


If the Suzuki scanner is used, connect the Suzuki scanner to the DLC 1 socket, the switch of ignition has to be in the provision of "OFF" (fig. 2.33).

Start the engine and warm up it up to the normal working temperature.
Make sure that all electric consumers, except ignition are switched off.
Make sure that rotation frequency idling – within norm.
Establish initial value of a corner of an advancing of ignition as follows.

Fig. 2.34. Conclusions D and E diagnostic sockets


Choose the MISC mode on the Suzuki scanner and establish initial value of a corner of an advancing of ignition. If at your disposal there is no scanner (cars without control lamp of an immobilizator), connect conclusions D and E diagnostic sockets 1 crossing point to establish initial value of a corner of an advancing of ignition (fig. 2.34).

Fig. 2.35. Use of a stethoscope


Using a stroboscope 1, check adjustment of the mechanism of gas distribution (fig. 2.35).
Initial installation of a corner of an advancing of ignition: 5 +3 ° to the top dead point (idling) the Operating procedure of cylinders 1-3-4-2.
If installation of a corner of an advancing of ignition – differs from norm, check the following:
– sensor of position of the crankshaft;
– plate of the sensor of position of the crankshaft;
– sensor of provision of a butterfly valve;
– switching signal chain;
– VSS;
– installation of a cover of a chain of the drive of the mechanism of gas distribution.
After check of initial installation of a corner of an advancing of ignition, cancel compulsory installation of a corner of an advancing of ignition the SUZUKI scanner or disconnect a crossing point from the diagnostic socket.
In the idling mode (the butterfly valve is closed, and the car is stopped) check installation of a corner of an advancing of ignition – about 3-17 ° to the top dead point. (A constant deviation within several degrees of 3-17 ° do not point to an aberration, but confirm functioning of an electronic control system of an ignition advancing corner).
Besides, check increase in a corner of an advancing of ignition with increase in frequency of rotation of the engine.
If results of check indicate an aberration, check the sensor of position of the crankshaft, a chain of the scheme of management and an electronic control unit.

"previous page
2.1.15. Check of the coil of ignition (with igniter)
following page"
2.2. Mechanical part of engines