Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
6.1. General description
6.1.1. Design of the brake system
6.1.2. Check of pressure (if there is LSPV pressure limiter)
6.1.3. Check of height of a pedal of a brake
6.1.4. Removal of air from the brake system
6.1.5. Removal and installation of the hose / pipeline of the forward brake mechanism
6.1.6. Removal and ustanovkashlang / pipeline of the back brake mechanism
6.1.7. Check of brake hoses and pipelines
6.1.8. Removal and installation of the tank of the main cylinder
6.1.9. Removal and installation of the main cylinder
6.1.10. Dismantling and assembly of the main cylinder
6.1.11. Assembly of the main cylinder
6.1.12. Check of the main cylinder
6.1.13. Amplifier of brakes
6.1.14. Removal and installation of the amplifier of brakes
6.1.15. Check and adjustment of the amplifier of brakes
6.1.16. Removal and installation of the limiter of pressure depending on loading
6.1.17. Check and adjustment of the parking brake system
6.1.18. Removal and installation of a cable of the parking brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 






6-1-16-snyatie-i-ustanovka-ogranichitelya-davleniya-v-zavisimosti-ot-nagruzki.html

6.1.16. Removal and installation of the limiter of pressure depending on loading

ATTENTION
Never disassemble pressure limiter depending on loading. At the same time its work will be broken. If the limiter is faulty, replace it with new (fig. 6.38).

Removal
Clear the place around a cover of the tank and pump out liquid the syringe.
Lift the car on the elevator.
Disconnect brake highways from pressure limiter.

Fig. 6.39. Removal of the limiter of pressure


Turn off bolts of fastening 3 and an adjusting nut of 2 (fig. 6.39).
Remove the limiter of pressure 1 with a spring 4 from a body of the car (fig. 6.39).

Installation
Install pressure limiter depending on load with a spring of a car body.

Fig. 6.40. Places of putting lubricant


Apply multi-purpose jellied grease on the top and lower hinge of 1 tsil.pruzhina (fig. 6.40).

Fig. 6.41. Bolts and nuts of the brake highway and bolt of fastening of the limiter of pressure


Tighten all bolts and nuts the nominal force of an inhaling, as shown in the figure 6.41.

Inhaling moments
Adjusting nut of the limiter of pressure depending on loading And: 23 N · m.
Nut of the brake highway B: 16 N · m.
Bolt of fastening of the limiter of pressure depending on loading (c): 23 N · m.
Fill the tank with brake fluid and remove air from the brake system.
After removal of air check correctness of installation of the limiter of pressure depending on loading, see. "Check and adjustment of the limiter of pressure depending on loading".

Check and adjustment of the limiter of pressure depending on loading
Before check and adjustment.
– The fuel tank has to be completely filled with fuel.
– The car has to be equipped with a spare wheel, the tool and a jack with the handle.
– The car should not bear any other loading.
– The car has to be installed on a plain horizontal surface.
Transfer pressure limiter lever in a finger to extreme situation and measure length of a cylindrical spring ("a" in the figure 6.42).
Length of a spring of "a": 142 mm.

Fig. 6.42. Measurement of length of a cylindrical spring


If it not so, adjust length of a spring having moved it, as shown in the drawing. After adjustment, tighten a nut 1 nominal force of an inhaling (fig. 6.42).
The moment of an inhaling of an adjusting nut of the limiter of pressure depending on loading And: 23 N · m.

NOTE
Make sure that pressure limiter case depending on loading and connection of brake pipelines have no liquid leak traces. Replace all defective parts.

Check liquid pressure, see. "Check of pressure of liquid (if there is pressure limiter depending on loading)".

"previous page
6.1.15. Check and adjustment of the amplifier of brakes
following page"
6.1.17. Check and adjustment of the parking brake system