Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
2.1. Preliminary checks
2.2. Mechanical part of engines
2.3. Engine cooling system
2.4. Engine lubrication system
2.5. Fuel system
2.5.1. Precautionary measures at service of fuel system
2.5.2. Description of fuel system
2.5.3. Description of a fuel supply system
2.5.4. Description of the fuel pump
2.5.5. Procedure of dumping of pressure of fuel
2.5.6. Procedure of check of leak of fuel
2.5.7. Removal and installation of a fuel pipe
2.5.8. Removal and installation of a fuel nozzle
2.5.9. Check of a fuel nozzle
2.5.10. Removal and installation of the regulator of pressure of fuel
2.5.11. Check of a cover of a jellied mouth of the fuel tank
2.5.12. Removal and installation of the fuel tank
2.5.13. Procedure of cleaning of the fuel tank
2.5.14. Removal and installation of the inlet valve of the fuel tank
2.5.15. Check of the inlet valve of the fuel tank
2.5.16. Check of the fuel pump on the car
2.5.17. Removal and installation of the fuel pump assembled
2.5.18. Dismantling and assembly of the fuel pump
2.6. System of ignition
2.7. System of release
2.8. The engine and system of decrease in toxicity of the fulfilled gases (M13 and M16 engines)
2.9. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 






2-5-18-razborka-i-sborka-toplivnogo-nasosa.html

2.5.18. Dismantling and assembly of the fuel pump

Sort and repeatedly collect the fuel pump, in view of the following.

ATTENTION
At removal of the fuel level sensor, do not concern a plate of the resistor 1 and you watch to deforming the lever 2. It can lead to failure of the fuel level sensor.

At removal of the condensing ring from a fuel tube or an arm you watch to damaging established (in an opening) a part of the condensing ring. In case of damage of a ring replace it new, otherwise, in this place fuel leak is possible.

Fig. 2.259. Removal of the fuel level sensor


At removal of the fuel level sensor 3, press on a clamp 4 and shift it in the direction of an arrow, as shown in the figure 2.259.
At installation of the fuel level sensor on the case, you watch that it was reliably fixed.

Check of the fuel pump
Check the fuel pump for existence of damages.

Fig. 2.260. Fuel filter and fuel level sensor


Check the fuel filter 1 for availability of dirt and a contamination (fig. 2.260).
If this is so, replace or clear and check the fuel tank for dirt availability inside.
For check of work or check of an electric part see.
For check of the fuel level sensor 2 (fig. 2.260).
Valve check of adjustment of pressure in a tank is made as follows.

ATTENTION
Do not suck away air through a hose of removal of vapors of fuel. Vapors of fuel constitute health hazard.


Fig. 2.261. Fuel supply valve purge


At a purge air has to pass without hindrances through the valve 2 from a hose of removal of vapors of fuel 3 from "A" to "B" (fig. 2.261).
Besides, at connection of the vacuum pump to a hose of removal of vapors of fuel and air supply from the pump has to pass through the valve, air from "B" to "A".
If air does not pass through the valve when performing operation a, or when performing operation b. Vacuum remains, replace the fuel filter assembled with 1 (fig. 2.261).

Inhaling moments

"previous page
2.5.17. Removal and installation of the fuel pump assembled
following page"
2.6. System of ignition