Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
2.1. Preliminary checks
2.2. Mechanical part of engines
2.2.1. General description of the engine
2.2.2. Removal and installation of the filtering element of the air filter
2.2.3. Adjustment of a cable of the drive of a butterfly valve
2.2.4. Removal and installation of a throttle branch pipe
2.2.5. Dismantling and assembly of a throttle branch pipe
2.2.6. Cleaning of a throttle branch pipe
2.2.7. Removal and installation of a throttle branch pipe and inlet collector
2.2.8. Removal and installation of a cover of a head of the block of cylinders
2.2.9. Removal and installation of the power unit
2.2.10. Removal and installation of a cover of a chain of the drive of the mechanism of gas distribution
2.2.11. Cleaning and check of a cover of a chain of the drive of the mechanism of gas distribution
2.2.12. Removal and installation of a chain of the drive of the mechanism of gas distribution and natyazhitel of a chain
2.2.13. Check of a chain of the drive of the mechanism of gas distribution and natyazhitel of a chain
2.2.14. Removal and installation of a cam-shaft, pusher of the valve and adjusting laying
2.2.15. Check of a cam-shaft, pusher of the valve and adjusting laying
2.2.16. Dismantling and assembly of a head of the block of cylinders
2.2.17. Check of valves and the directing plugs of valves
2.2.18. Check of a head of the block of cylinders
2.2.19. Check of a valvate spring
2.2.20. Removal and installation of pistons, piston rings and rods
2.2.21. Dismantling and assembly of pistons, piston rings, rods and cylinders
2.2.22. Check of cylinders, pistons and piston rings
2.2.23. Check of piston fingers and rods
2.2.24. Check of conrod necks and conrod bearings
2.2.25. Removal and installation of radical bearings, bent shaft and block of cylinders
2.2.26. Check of a bent shaft
2.2.27. Check of radical bearings
2.3. Engine cooling system
2.4. Engine lubrication system
2.5. Fuel system
2.6. System of ignition
2.7. System of release
2.8. The engine and system of decrease in toxicity of the fulfilled gases (M13 and M16 engines)
2.9. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 










2-2-14-snyatie-i-ustanovka-raspredvala-tolkatelya-klapana-i-regulirovochnojj-prokladki.html

2.2.14. Removal and installation of a cam-shaft, pusher of the valve and adjusting laying

Fig. 2.84. Details of a cam-shaft, pusher of the valve and adjusting laying: 1 – cam-shaft of the drive of inlet valves; 2 – cam-shaft of the drive of final valves; 3 – laying; 4 – valve pusher; 5 – camshaft case; 6 – camshaft case bolt



Removal
Uncover a gas distribution mechanism drive chain.
Remove a gas distribution mechanism drive chain.

Fig. 2.85. Order of weakening of bolts of fastening of the case of the camshaft


Weaken camshaft case bolts in the order shown in the figure 2.85 and completely turn off them.
Remove cases of camshafts.
Remove cam-shafts of the drive of inlet and final valves.

Fig. 2.86. A valve 2 pusher with adjusting laying 1


Remove pushers of valves 2 with adjusting laying of 1 (fig. 2.86).

Installation

Fig. 2.87. Installation of a pusher


Establish pushers of valves and adjusting laying in a head of the block of cylinders. Apply engine oil on the periphery of a pusher of the valve, then establish it in a head of the block of cylinders (fig. 2.87).

NOTE
At installation of adjusting laying, make sure that the party of laying on which No. is put is turned to a valve pusher.

Establish cam-shafts 1.

Fig. 2.88. Combination of tags on asterisks at installation of cam-shafts


Apply engine oil on the surfaces of friction of each cam-shaft and basic necks of a cam-shaft, then establish them, as shown in the figure 2.88.

NOTE
Before installation of cam-shafts turn a bent shaft so that the shponochny groove was turned up.


Fig. 2.89. Pin of the case of the camshaft 1


Fig. 2.90. Control position of cases of the camshaft: A – the party of an admission or E – the party of release; B – situation from a gas distribution mechanism drive chain; C – specifies towards a gas distribution mechanism drive chain



Establish pins of the case of the camshaft 1, as shown in the figure 2.89.
On each case of the camshaft there are relief tags which, specify situation and the direction of installation. Install cases on these tags.

Fig. 2.91. Order of tightening of bolts of fastening of the case of the camshaft


Oil engine bolts of cases and tighten them at first temporarily. Then tighten them in the order shown in the figure 2.91. Tighten bolts gradually, at the same time and exactly, repeat the sequence of an inhaling two or three times before finally to tighten bolts nominal force.
Inhaling moment bolts of the case of the camshaft (a): Tighten the moment 11 N · m.
Establish a gas distribution mechanism drive chain with an asterisk of a bent shaft.
Establish a gas distribution mechanism drive chain cover.
Check gaps in valves.

"previous page
2.2.13. Check of a chain of the drive of the mechanism of gas distribution and natyazhitel of a chain
following page"
2.2.15. Check of a cam-shaft, pusher of the valve and adjusting laying