Suzuki Liana since 2002
1. Operation and maintenance of the car
2. Engine
2.1. Preliminary checks
2.2. Mechanical part of engines
2.2.1. General description of the engine
2.2.2. Removal and installation of the filtering element of the air filter
2.2.3. Adjustment of a cable of the drive of a butterfly valve
2.2.4. Removal and installation of a throttle branch pipe
2.2.5. Dismantling and assembly of a throttle branch pipe
2.2.6. Cleaning of a throttle branch pipe
2.2.7. Removal and installation of a throttle branch pipe and inlet collector
2.2.8. Removal and installation of a cover of a head of the block of cylinders
2.2.9. Removal and installation of the power unit
2.2.10. Removal and installation of a cover of a chain of the drive of the mechanism of gas distribution
2.2.11. Cleaning and check of a cover of a chain of the drive of the mechanism of gas distribution
2.2.12. Removal and installation of a chain of the drive of the mechanism of gas distribution and natyazhitel of a chain
2.2.13. Check of a chain of the drive of the mechanism of gas distribution and natyazhitel of a chain
2.2.14. Removal and installation of a cam-shaft, pusher of the valve and adjusting laying
2.2.15. Check of a cam-shaft, pusher of the valve and adjusting laying
2.2.16. Dismantling and assembly of a head of the block of cylinders
2.2.17. Check of valves and the directing plugs of valves
2.2.18. Check of a head of the block of cylinders
2.2.19. Check of a valvate spring
2.2.20. Removal and installation of pistons, piston rings and rods
2.2.21. Dismantling and assembly of pistons, piston rings, rods and cylinders
2.2.22. Check of cylinders, pistons and piston rings
2.2.23. Check of piston fingers and rods
2.2.24. Check of conrod necks and conrod bearings
2.2.25. Removal and installation of radical bearings, bent shaft and block of cylinders
2.2.26. Check of a bent shaft
2.2.27. Check of radical bearings
2.3. Engine cooling system
2.4. Engine lubrication system
2.5. Fuel system
2.6. System of ignition
2.7. System of release
2.8. The engine and system of decrease in toxicity of the fulfilled gases (M13 and M16 engines)
2.9. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 










2-2-5-razborka-i-sborka-drosselnogo-patrubka.html

2.2.5. Dismantling and assembly of a throttle branch pipe

Fig. 2.44. Details of a throttle branch pipe and inlet collector: 1 – inlet collector; 2 – laying of an inlet collector; 3 – throttle branch pipe; 4 – laying; 5 – a tube of recirculation of the fulfilled gases; 6 – the sensor of absolute pressure in an inlet collector; 7 – valve of a purge of the filter of system of catching of vapors of gasoline; 8 – sensor of provision of a butterfly valve; 9 – idling regulator; 10 – fuel supply pipe; 11 – element of rigidity of an inlet collector; 12 – nut of fastening of an inlet collector; 13 – bolt of fastening of an inlet collector (short); 14 – bolt of fastening of an inlet collector (long); 15 – laying of a tube of system of recirculation of the fulfilled gases; 16 – sealing ring; 17 – the condensing ring; 18 – block of a fuel nozzle; 19 – laying; 20 – bolt of fastening of a pipe of supply of fuel



Dismantling
Remove the sensor of provision of a butterfly valve and the valve of the regulator of idling from a throttle branch pipe.

NOTE
During the dismantling and assembly of a throttle branch pipe observe extra care not to deform levers on a shaft of a butterfly valve or not to damage any other details.

Assembly
Install the idling regulator valve on a throttle branch pipe.
Install the sensor of provision of a butterfly valve on a throttle branch pipe "With".

"previous page
2.2.4. Removal and installation of a throttle branch pipe
following page"
2.2.6. Cleaning of a throttle branch pipe